Plumbing Basics: An Essential for Installing a Bathtub
Click HereWe have noticed this article about Tools You Need to Install a New Bathtub down the page on the net and think it made good sense to share it with you on this page.
Setting up a tub isn't specifically rocket science, but it does require strong plumbing, woodworking, as well as sometimes, tiling skills. Replacing an old bathtub with a new one is likewise a reasonably challenging job. If the old tub is readily available, the task can move quickly; if you need to open a wall surface to eliminate the old bathtub and place the brand-new tub, the task is much harder. In either case, the job is within a residence handyman's abilities, although you will require a helper to vacate the old tub and also embeded in the brand-new one. Ensure you have actually certified yourself for the job and also fit attempting it. Instead of working with a specialist to take over a halfway-completed job, it is far better to think about using one before you begin. Possibilities are you might require a specialist plumber to make tube links.
This short article will certainly aid you set up a new bath tub in your bathroom if you have actually currently purchased a brand-new tub as well as don't need to transform the setup of your previous water supply pipelines.
Your devices and material list ought to consist of the following:
Planning for the Setup
To start with, the supporting structure provided with the bath needs to be fitted (if needed) according to the producer's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is necessary to ensure that if the faucet features a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets system to stop strain on the bath tub.
Fit the versatile faucet ports to the bottom of the two taps utilizing 2 nuts and olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet via the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you make use of all of the provided washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bath must currently prepare to be fitted in its final placement.
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your setup, after that the first thing you ought to do is disconnect the water supply. After doing so, turn on the taps to drain pipes any type of water remaining in the system. The procedure of eliminating the existing faucets can be rather bothersome as a result of the limited gain access to that is often the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipes to the faucets. Have a cloth all set for the staying water that will come from the pipes. As soon as the supply pipelines have been eliminated, use the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the single taps from turning during this procedure. As soon as the faucets have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any type of old securing substance.
Before carrying on to fit the brand-new faucets, contrast the pipe links on the old taps to the new taps. If the old taps are longer than the new taps, then a shank adapter is required for the brand-new faucets to fit.
Mounting the Bath tub
Using both wood boards under its feet, put the tub in the needed position. The wooden boards are practical in equally spreading out the weight of the tub over the area of the boards as opposed to concentrating all the weight onto 4 tiny points.
The following objective is to make certain that the tub is leveled all round. This can be achieved by examining the level as well as changing the feet on the bathtub up until the spirit level reviews level.
To set up faucets, fit all-time low of the furthest versatile faucet port to the ideal supply pipe by making a compression join; then do the same for the other tap.
Turn on the water system and examine all joints as well as brand-new pipework for leakages and also tighten them if needed. Fill the tub and additionally inspect the overflow outlet and the regular electrical outlet for leakages.
Lastly, take care of the bath paneling as described in the manufacturer's instruction manual. Tiling as well as sealing around the bathtub should wait till the tub has been made use of at the very least once as this will certainly resolve it into its final position.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic connector to avoid damages to the thread. One end of the adapter fits on the plastic tail of the tap as well as the various other end offers a link to the current supply pipes.
If you need to fit a monobloc, after that you will certainly require minimizing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, place the faucet in the installing opening in the bath/basin making sure that the washing machines are in area in between the tap as well as the sink. Secure the faucet in place with the maker offered backnut. When the faucet is firmly in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with normal tap connectors. The former type needs to be attached to the faucet ends first, tightening only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the area where the bathroom fulfills the floor tile, it is needed to secure the joins with a silicone rubber caulking. This is essential as the fitting can relocate enough to fracture a stiff seal, creating the water to permeate the wall between the bathroom and the tiling, bring about problems with wetness as well as possible leaks to the ceiling below.
You can choose from a selection of coloured sealers to assimilate your components and installations. They are offered in tubes as well as cartridges, and can securing spaces up to a width of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with spins of soaked newspaper or soft rope. Remember to always load the bath tub with water prior to sealing, to enable the movement experienced when the bathtub remains in use. The sealer can split rather very early if you do not think about this activity prior to sealing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also conveniently available on the marketplace. It is a good idea to fit the tiles utilizing waterproof or water-proof adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I found that piece of writing on Installing A Bathtub when doing a lookup on the internet. Sharing is good. Who knows, you may be helping someone out. I am grateful for your time. Please stop by our website back soon.
Quote